1-3 working days delivery for in stock items (unless stated otherwise on the product page); may be longer for rural postcodes.
FREE DELIVERY to London and other selected postcodes on selected items only on orders over £250
For more information click here
A self-adhesive high quality, high density, open cell foam sealing tape which has been impregnated to a high level with acrylics and FR additives. The product is CFC- and HCFC-free and contains no chloride compounds. When the Xpandafoam foam tape is compressed the cells close thus providing for a variety of sealing applications as detailed below:
Xpandafoam tape is supplied pre-compressed for ease of application. All coils have a reinforced self-adhesive backing. When the rolls are opened the tape expands to about 5 times its compressed thickness. The product is designed to accommodate movement in joints and seals against uneven surfaces. For full acoustic and weather sealing applications you do not want the tape to expand fully. For example EXP5/12 comes 5mm thick before opened and should not be allowed to expand further than 12mm for best results.
The elasticity and flexibility is such that it will seal gaps between uneven surfaces such as brickwork and concrete and maintains its elasticity and responds continually to expansion and contraction cycles without any joint failure. Tests to monitor the life expectancy reveal no significant deterioration over 20 years in use.
Xpandafoam is also ideal as as a weatherstripping material to fill expansion joints or for the filling of voids. It will create a draught, dust, wind and driving rain seal and has a guaranteed life span of 20 years. Approved to DIN 4102 and DIN 18542 the tape is compatible with most other building materials.
We recommend using Xpandafoam when installing our acoustic doors to give the maximum acoustic benefits. The 5mm gap between the structure and the frame must be sufficiently sealed to prevent noise leakage around the door. Using this product along with our fire rated flexible acoustic sealant will maintain the acoustic and fire integrity of the door assembly.
Xpandafoam can also be used around the perimeter of acoustic floors and acoustic ceilings. It is also ideal for sealing gaps between pipes and services where they penetrate through a wall or floor.
|Tape Type||Full Expansion||Coil Length|
|EXP1/4||expands to 9mm||13m|
|EXP4/9||expands to 21mm||8m|
|EXP5/12||expands to 28mm||5.6m|
|EXP6/15||expands to 36mm||4.3m|
|EXP9/20||expands to 47mm||3.3m|
|EXP11/25||expands to 60mm||2.6m|
|EXP18/24||expands to 95mm||3.3m|
|EXP24/42||expands to 120mm||2.6m|
|We can cut to any width, 25mm is generally a standard width but user to specify|
|Foam||Polyurethane with impregnation|
|Colour||Black or grey|
|Thickness||Pre-compressed rolls, one side self adhesive
length of roll: 2–13m depending on thickness
thickness: 10–150mm (decompressed)
|Tensile strength DIN 53 571||At least 100kPa|
|Tensile elongation DIN 53 571||At least 200%|
|Compressive strength at a compression of +40°C DIN 53 577||ca. 3,4 kPa (+/- 15%)|
|Behaviour under fire DIN 4102-1||B1 (P-NDS04-284)|
|Temperature resistance||-30°C until +100°C + 130°C for short time|
|Permeability of joints DIN EN 1026 (DIN EN 42)||coefficient of joint permeability a<0,1 m³/.hm (daPa)n|
|Water tightness under heavy rain wind force: 11/height of building: 100m DIN EN 1027 (DIN EN 86)||>600 Pa / stress group B1 (wind force: 11 / height of building: 100m)|
|Weathering resistance||< 10 years|
|Thermal conductivity||0.07 W/mK|
1. Storage and surface preparation
Tape should be stored in a warm, dry, interior location. Ideal application temperature is approximately 24°C. Expansion will be faster at higher temperatures and slower at lower temperatures. Full expansion normally takes about 24hrs from when the material is first opened but when re-compressed it will re-expand within minutes. For faster expansion in cold conditions keep the material warm before use and, if desired, apply heat from a hair dryer to installed material to accelerate expansion.
Joint faces should be dry and cleaned of dirt, oil and grease etc. There should be sufficient depth to receive the full width of the tape.
IMPORTANT: Reels should be stored flat and kept compact. Should material expand in package it can still be used. Unroll the material, allow it to expand, then recompress it between surfaces to be sealed.
2. Opening reels
Only open rolls that will be used immediately.
3. Square off ends
Start and finish ends must be cut square. For easier cutting spray the knife or scissors with a mist of water.
4. Peel off liner
A suitable length or section should be cut to fit the opening. The material only expands in one direction i.e. its thickness, not its width. For acoustic purposes we recommend that it not be allowed to expand more than 35% of its fully expanded thickness so its important to check the gap size before using (or ordering) the material. For larger gaps two layers can be stuck one on top of the other. Remove release liner to expose the adhesive backing face of the tape.
5. Adhere to surfaces
Position the tape and press to secure. If needed, cut and fit smaller filler pieces of tape to fill panel or corrugation voids.
6. Join lengths with mitres
To form a continuous strip overlap tapes and miter with a moist knife at a 45° angle. Pinch the mitered faces together.
Please note: This product is for use as an acoustic expansion gap seal it is not designed to be an Intumescent Expansion Gap product. If you are looking for a fire rated acoustic intumescent product please click here