Part E Low Cost Acoustic Floating Floor

Part E Low Cost Acoustic Floating Floor
Product Code: A325
Availability: In Stock
Download Description: For Registered Users Only
Price: £82.50

Revit BIM family object available A Revit / BIM Family object file is available for this product.

Isobase R50 5mm acoustic resilient flooring

  • Separating floors
  • Timber floors
  • Part E compliant resilient layer
  • Part E compliant
  • Provides significant reduction in impact noise and vibration
  • Easy to install
  • Only 5mm thick does not significantly increase the floor level

5mm IsoBase R50 is designed to provide excellent acoustic sound insulation with ease of installation. The product is designed to be used as a resilient layer underneath T&G chipboard type flooring, along with a suitable ceiling treatment, as shown in the diagrams below.

General physical data
Roll size 15m x 1m
Colour Grey
Thickness 5mm
Thermal conductivity 0.037 W/mK
Compressive strength at 25% >23±2 kPa
Modulus of elasticity >5 kPa
Dynamic stiffness <95 MN/m³
Recyclable content 100%
Full system fire protection 60 minutes

Incorporating the latest changes to the Approved Document E 2003, the minimum and maximum sound insulation requirements for separating floors are as follows:

  Airborne sound reduction DnTw+C;tr Impact sound level LnTw
Conversion 43dB or greater 64dB or less
New build 45dB or greater 62dB or less

To comply with the requirements of the  Approved Document E 2003, IsoBase R50 sound insulated separating floors have been tested in accordance with BS EN ISO 140-6:1998 and rated in accordance with BS EN ISO 717-2:1997.

isobase acoustic resilient layer installed under chipboard flooring >isobase r50 acoustic test data

Lab Tested Performance of the Above Structure:-
  Airborne              Impact
Rw=59dB (Ctr-10)    Lnw59dB
Rw+ Ctr= 49dB

Recent on site test results have been:
DnT,w+ Ctr 49dB 48dB 49dB 43dB
LnT,w 53dB 57dB 53dB 51dB

Further improvements can be made by placing 19mm Gypsum based plank over the IsoBase R50 before installing the 22mm T&G Chipboard.
If this is undertaken first then improved results will be in the order of:
  Airborne              Impact
Rw=62dB (Ctr-8)    Lnw54dB
Rw+ Ctr= 54dB

isobase r50 acoustic floor system upgraded with 19mm plank

Domestic Soundproofing - Higher performing remedial flooring upgrade options

Retained existing floorboards

Sometimes customers want to add acoustic insulation but keep the existing floorboards especially if the property has period ones. This can often be problematic. A very simple, but nominal, improvement can be achieved by adding the 100mm acoustic mineral wool into the floor cavity, stapling the VL-65 Acoustic Membrane over the joists before screwing back the boards. This does not, however, add very much isolated mass to the floor so improvements will not be ideal. Improvements in airborne noise will be better than improvements in impact noise. Fitting a strip of our high density resilient floor tape along the tops of the joists before screwing down the floorboards will help a little with improved impact noise transfer especially if you use screws sparingly. It is not 100% ideal as there will be screw fixings but it is better than doing nothing.

Ideally acoustic mineral wool, or even better the 2FTex acoustic quilt should first be inserted between the joists. If using mineral wool in this application it would be much better to use the 140kg version and do not go any lower than the 60kg version.

isobase r50 with retained floorboards remedial acoustic floor upgrade

A much better solution which will greatly reduce impact and airborne noise transfer is to use the system shown below. This involves an isolation layer of IsoBase R50 along with heavyweight damping sheet VL65 to form a much heavier and isolated acoustic sandwich. The top layer of chipboard is floated on the R50. The floorboards can be screwed, or nailed, through the T50 and into the top chipboard layer but these screws or nails must not penetrate through into the green IsoBase layer or the acoustic isolation will be breached and the system will not work effectively. Attention to detail should be paid at the room perimeter. You need to make sure the flanking strip keeps the chipboard from touching the wall and also make sure the floorboards are not touching the walls or the skirting board.

remedial acoustic floor upgrade using isobase r50

Replacing a carpet with laminate or engineered flooring

If you take up an existing carpet with good underlay and want to replace it with laminate or engineered floor you are likely to have complaints from downstairs. In situations like this you really need a double isolation layer, one between a base board and the joists and then another between the laminate floor and the baseboard floor. This would involve not only this product but also using a high performance wood/laminate underlay between the two sections.

acoustic floor remedial upgrade using isobase r50

These solutions above do raise the floor height which may be a problem but they are necessary because you are likely to not be treating the underside of the ceiling below. The above solutions are also in some ways easier if you do not want to lift the existing base floor for any reason. Obviously you need to lift the floor to install mineral wool or 2FT80 in the cavity space and if this is the case then there are a few options for reducing the overall floor height rise. If thinner solutions are desired you could consider using our high density resilient floor tape or the joist caps directly on top of the joists and then floating the base floor of T&G chipboard on this material. It does away with the 5mm IsoBase layer and the 18mm chipboard base thus saving around 11–17mm depending on which product you use.

acoustic floor remedial upgrade domestic soundproofing

Write a review

Your Name:

Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:

Noise Control Soundproofing and Acoustics © 2022
View Mobile / Standard